FS: 300whp Turbo Escort
 

Since my initial post was deleted - here's another more thorough FS thread. PM me with your email for pictures or any questions.

This has been my pride and joy for over 5 years. I have built this car up to what it is today from the ground up. The car is very reliable - you can drive it to the track and back home and everything functional in the car is new or almost new.
The car makes around 280-300whp at 18-20psi. It weighs around 2500lbs. The turbo and motor are capable of in excess of 350whp On low boost(15 psi) it traps over 108Mph on street tires. It suits an experienced driver best and no test pilots or time wasters will be entertained. The modifications/build are listed below. Some highlights include a full forged motor, LSD transmission, fully tuned standalone. The parts chosen are OEM or better to retain reliability and driveability.

For those of you that don't know the motor in this vehicle is a DOHC BP - the same as that used in Miatas.

The car passes aircare and has done so for the last two years without issues without removing ANY parts from it. This can truly be a weekend warrior and a grocery getter. It is best suited for someone who will take it to the track and around corners

The car has its exterior blemishes. The paint is not in great shape as is expected of an 18 year old car. It was never meant to be a show car, it was always meant to perform and be driven.

Chassis has 244 000km on it. The brand new engine, clutch, transmission have 10 000 km on them. There is nothing broken or wrong with the car and it can be driven to the track or mall the moment you pick it up.

$7000 OBO and of course there is some flexibility but serious inquiries only

For pictures please PM me or see this ad: http://vancouver.en.craigslist.ca/va...356004820.html

Parts list:

Engine:
Fully built and balanced engine 10000km ago. 190psi compression in all cylinders
- H beam forged rods
- Wiseco 9:1 pistons ceramic coated and PC9 sideskirt coated by Swain
- Clevite bearings
- Flying Miata gasket set
- Head with ported exhaust, Turbo cams
- ARP head and main bearing studs
- External oil cooler with -8AN lines
- Port matched exhaust and intake manifolds
VJ23 ball bearing turbo with Mazda GTR (AWD homologation vehicle) exhaust manifold. Turbo is bigger than a GT28 but smaller than a GT30. Water and oil cooled from the Mazda GTR rally car
Mazda GTR intake manifold
Heat insulator gaskets for throttle body
Megasquirt I Extra HR controlling fuel and ignition with following modifications:
- PWM idle air control
- Boost Control
- Wasted spark control
- Knock sensor input
2003.5 Mazdaspeed Protégé LSD welded for strength
Mazdaspeed transmission, jackshaft, axles
SPEC AWD Mazda GTR clutch capable of handling over 350 ft lbs of torque
550cc RC low impedence injectors
Vishnu dual feed fuel rail
HKS SSQV blow off valve
4-wire TPS
21x9x3 FMIC with 2.5" inlets
Full 2.5" mandrel bent intercooler piping
3" turbo back exhaust
Highflow cat, no resonator
Magnaflow 3" muffler
MSD Blaster SS coil
Walbro 255 l/h fuel pump
B&M short shifter
Solid front and rear motor mounts
Delete A/C, Cruise, and power steering

Suspension and Footwork:
Ground Control ZX2 coilovers
Tokico S/R struts
Tokico strut mounts front and back
Front and Rear Corksport upper strut bars
Energy solid swaybar bushings front and back
MX3 rear tie bar
Front lower tie bar
Front and rear ST add-on swaybars
Professional 4 point roll cage (not yet installed) making this car legal for Solo racing
SS braided brake lines
Brembo front and rear rotors
Hawk HPS pads all around
16x7 Rota Subzero rims
Hankook Ventus tires (205/45/16) with 75% tread left

Misc:
MX-3 recaro style front seats
Autometer Boost, Oil pressure, and EGT gauge
AEM wideband O2
Aftermarket headunit and Clarion front speakers
2 way paging alarm

Bump. Car just ran 13.6 on 205 series street tires last night at Mission.

bump. Car is safe and sound for the winter and waiting for a driver for the summer.