REVscene Automotive Forum

REVscene Automotive Forum (https://www.revscene.net/forums/)
-   USED Automotive Performance Parts ONLY (https://www.revscene.net/forums/used-automotive-performance-parts-only_23/)
-   -   FS: Parting out RB26DETT, other random stuff (https://www.revscene.net/forums/663847-fs-parting-out-rb26dett-other-random-stuff.html)

RBS13 02-28-2012 04:48 PM

FS: Parting out RB26DETT, other random stuff
 
Sold my car and dont need to build the rb26 anymore so im selling it. Disassembled at 60,000kms to replace seals and gaskets while it was out, was in perfect working order with 145-150 compression across the board. Below are prices that are OBO but what i feel to be fair, more stuff bought = better deal so dont be afraid to shoot an offer. Everything will be PLUS shipping.

Bare 05U Block, hot tanked,magnafluxed and quick hone painted black,comes with cradle and squirters - $450

OEM R32 crank, should get a collar but clean otherwise,no scoring- $150


Polished Valve covers 8/10 condition could use a quick reshine - SOLD
cam covers, coil cover and front timing cover)

Complete RB26 engine harness, uncut - $250

1 complete set of 6 OEM pistons and rods complete with rings, very minimal det on 2 piston tops , have been wire wheeled and cleaned(had good compression but rings should be replaced anyways so im not saying to use them) - $100

1 set of OEM Pistons, and wrist pins - $50

2 Stock GTR Turbos, minimal shaft play, no smoke, semi polished housings and polished wg actuators - $250, can include stock manifolds,elbows aswell

RB26 Y-Pipe for turbos- $60

2 GTR Mafs - $80 pair

3 Cam angle sensors - $70 each (tested working condition)

Rb20/26 ignitor - $70 (tested and working )

Greddy clear timing cover, says RB26 on it, one small crack at bottom- $70

OEM Valve seals intake and exhaust - $40

OEM valves, springs, retainers - $100 pending

OEM camshafts - $50 a set, have 2 sets

OEM water pump - $30

Intake plenum assembly, with ITB's and AAC valve - SOLD

Fuel rail - $40

Injector resistor box - $50

GTR rear 6 bolt axles, hubs (one needs a bearing) and R200 diff - $150

Blitz intake filters and adaptors - $140

BNIB supertech intake and exhaust valve guides RB26- $100

Coilpack harness - $40

GTR front drive shaft - $50

GTR rear drivshaft - $80

Stock RB20 ECU - $90

RB20 polished valve covers and custom vented coilpack cover powdercoated black - $100

RB25 intake OEM intake plenum - $80

RB20 intake plenum OEM- $80

RB26 knock sensors - $60 for the pair...crazy expensive new

If you need anything not listed PM me and i may have it. Parts located in Kelowna BC Canada, will ship! No paypal, EMT ONLY! Thanks

RBS13 03-01-2012 07:29 PM

bump, some parts sold! Also have 1JZ i will be disassembling shortly (no compression in 1 cylinder) if anything is needed shoot PM

RBS13 03-01-2012 08:10 PM

bump, parts to add




AEM 30-2001 Bosch Wideband Sensor BNIB - $50

spoon.ek9 03-02-2012 06:45 PM

actually, we would appreciate if you make a separate thread to keep the forums organized.

RBS13 03-04-2012 09:36 PM

well nobody wants to buy anything on here anyways, so delete it if need be. I dont have the time to post everything seperate


All times are GMT -8. The time now is 03:02 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
SEO by vBSEO ©2011, Crawlability, Inc.
Revscene.net cannot be held accountable for the actions of its members nor does the opinions of the members represent that of Revscene.net