Doodson
04-20-2010, 09:00 AM
I have a bunch of parts avail for CRX or CIVIC
AEM stand alone OBD0 computer with only dyno time ,comes with complete manual. - $500
full race prepped bottom end with weisco pistons , eagle H beam rods, oil scraper.... Motor ran for a 6 hour enduro and started to blow by. We think the piston rings did not seat proper? $700 takes it away and I have new rings for it aswell
8 galon ALT fuel cell with bladder, foam, 2 filler caps, in tank pump included - $350
New Altrom distributor / coil and complete MSD ignition including wires, SC ignition box - dyno time only - $350 - a distributor alone is close to this price
NEW- HONDA OE upper control arms - $50 each
Front '89 Si uprights (2) - new Moog ball joints, new o.e. hubs new NTN bearings and new ARP extended studs
$150 each side
Stock 4.25:1 trans w/ Kaaz LSD - $800
Stock Si tranny runs good , used as spare - $200
Endyn enduro prepared full race head with only 3 hours , valves/retainers/ race prep port and polish - $700 cost over $1500 US to have made.
1 stock cams (1 new in box o.e.) - $ 50
Skunk 2 manifold and large diameter throttle body with 3 hours - complete with AEM fuel rail - $400
Balanced and blueprinted injectors (used 1 season) included
AEM adjustable fuel pressure regulator - $50 no guage
AEM adjustable timing gear - $90
New in box o.e. Honda Master cyl - $100 7/8size
complete ES Urethane bushing kit (new) - $80
ES Urethane bushing kit (almost complete) - $50
Large diameter front sway bar 1 " - $80
Used radius rod spherical kit - $100
New in box MUGEN trailing arm bushings - $120
stiffer rubber
NEW Honda OE clutch cable - $30
cdoodson@shaw.ca
Got to clean the garage, these parts got to go
Thanx
Chris
AEM stand alone OBD0 computer with only dyno time ,comes with complete manual. - $500
full race prepped bottom end with weisco pistons , eagle H beam rods, oil scraper.... Motor ran for a 6 hour enduro and started to blow by. We think the piston rings did not seat proper? $700 takes it away and I have new rings for it aswell
8 galon ALT fuel cell with bladder, foam, 2 filler caps, in tank pump included - $350
New Altrom distributor / coil and complete MSD ignition including wires, SC ignition box - dyno time only - $350 - a distributor alone is close to this price
NEW- HONDA OE upper control arms - $50 each
Front '89 Si uprights (2) - new Moog ball joints, new o.e. hubs new NTN bearings and new ARP extended studs
$150 each side
Stock 4.25:1 trans w/ Kaaz LSD - $800
Stock Si tranny runs good , used as spare - $200
Endyn enduro prepared full race head with only 3 hours , valves/retainers/ race prep port and polish - $700 cost over $1500 US to have made.
1 stock cams (1 new in box o.e.) - $ 50
Skunk 2 manifold and large diameter throttle body with 3 hours - complete with AEM fuel rail - $400
Balanced and blueprinted injectors (used 1 season) included
AEM adjustable fuel pressure regulator - $50 no guage
AEM adjustable timing gear - $90
New in box o.e. Honda Master cyl - $100 7/8size
complete ES Urethane bushing kit (new) - $80
ES Urethane bushing kit (almost complete) - $50
Large diameter front sway bar 1 " - $80
Used radius rod spherical kit - $100
New in box MUGEN trailing arm bushings - $120
stiffer rubber
NEW Honda OE clutch cable - $30
cdoodson@shaw.ca
Got to clean the garage, these parts got to go
Thanx
Chris