FS/FT: Built DA with 5 lug ($9950!) 16K INVESTED!!
 

Thinkin about selling my car. This car is fantastic, i tried selling a while ago but couldnt do it. I've had this thing for 6 years now and life changes, things go on, time to move on. Still tryin to pull myself away from this but we'll see.



OVER 16K INVESTED! MAY EVEN INCLUDE ROYAL SPORT BRONZE ROTA GRID"S IN +20 OFFSET!!!!




For Trades im lookin for something 4door, most likely a Wrx Sti...along those lines.

Was $13,500...
Now $9950! will also include 01 ITR Cams installed!


**Just did a HID BI-Xenon retrofit from a 05 mercedes ml63 amg. Leave email for pics but only one word to describe it....SICK!

http://i157.photobucket.com/albums/t...r/102_1232.jpg
http://i157.photobucket.com/albums/t...r/102_1202.jpg


Quick lil exterior vid:

http://i157.photobucket.com/albums/t...h_102_0970.jpg

General rundown:
1991 Acura Integra RS
250,000 km on body
5,000 km on fresh engine
Had power locks installed with Ungo(clarion) Pager alarm
Even with this setup, im able to go to seattle and back on a tank of gas.(thats about 450km hiway)
I had 1 accident while i owned it in on the front right.
Never been stolen or broken into.

Update(December 18/07): Just re-did the front end 5 lug conversion. Got the hubs machined to fit my stock knuckle. It is now aligned perfectly with brand new wheel bearings, ball joints and tie rod ends. Also has Michelin pilot ice-x snow tires on steelies(195/55/15). Also Replaced a defective starter(Ac Delco sucks ass). Now running a Bosch starter.


Engine
06 Honda Civic OEM Battery & Tie-Down
97 GSR Block
AC Removal
AEM Fuel Rail
ARP Head Stud Kit
B&M Fuel Pressure Regulator Modifier(purple)
B18A1 LS Crankshaft
Custom Made Cold Air Intake
Eagle Forged Rods
Maule Forged Pistons
Engine Machining, cleanup, and balancing
ITR Cams
GSR Head
Mild Port and polish, intake and exhaust Port matched to head.
ITR Valve Cover
Skunk2 Valve springs and Ti retainers
OBX Header
Polyurethane Mount Inserts
Tanabe Hyper Medallion Catback exhaust
Skunk 2 Pro Intake manifold
STR Bronze Adjustable Cam Gears


Transmission/Drivetrain

01 ITR Change Rod
ACT Heavy Duty Clutch Kit
B&M Short Shifter
Fidanza 7lbs flywheel
Y1 cable tranny w/oem LSD

Suspension

Front upper strut tower bar
Skunk2 Sport Shocks and andjustable coilovers
Skunk2 front Upper control arms

Brakes

Apex Kevlar Brake pads (Front & Rear)
ITR 5 lug conversion all around
Earls Steel braided brake lines all around
GSR 1" Master Cylinder

Interior

Skunk 2 weighted shift knob
"A" pillar Triple Gauge Pod
Oil Pressure, Water Temp, & A/F Ratio gauges
Custom vtec engagement LED
Momo Steering Wheel

Exterior

1 piece headlights
8000k HID Kit
92-93 front bumper conversion
All Red Taillights
GSR & SiR DOHC VTEC Badging
ITR Style front lip
Licence Plate Relocated
Rear Lip

In Car Entertainment

Infinity Reference 6.25" front
JVC 5.25" 2 ways rear
Phenoix Gold Tweeters
JVD Head unit
Rockford Fosgate Amplifier
Rockford Fostgate Subwoofer in encloseure

Alloys & Tyres

205/45/16 BFGoodrich G-Force Sport
Gunmetal RSX Type S wheels
Spoon Sports lightweight lugs(anondized Red)

Engine Management

OBD1 Conversion
OBD1 O2 sensor/Distributor
P28 ECU W/ Jun Chip
Hondata S200 included(requires install and tuning) <tuning will be done before sale!
RyWire OBD0-OBD1 Jumper harness
Rywire vtec wiring harness


Ignition

MSD Blaster Coil
MSD Distributor Rotor
MSD Pro Distibutor cap
MSD SCI Ignition Box
MSD Spark Plug Wire Set
NGK Iridium Spark Plugs


New axles
New starter
New radiator
new lower ball joints and tie rod ends
many, many seals, gaskets, fluids, little maintnence things
wheel alignments after installing each mod.

Most Current Pictures are the ones with the RSX wheels:

http://i157.photobucket.com/albums/t...R/102_0883.jpg


http://i157.photobucket.com/albums/t...R/102_1009.jpg

http://i157.photobucket.com/albums/t...R/102_0894.jpg

With ITR wheels:

http://i157.photobucket.com/albums/t...rupdate081.jpg



With S2000 Wheels:


http://i157.photobucket.com/albums/t...cture01061.jpg


http://i157.photobucket.com/albums/t...rupdate060.jpg



http://i157.photobucket.com/albums/t...irdscar046.jpg



http://i157.photobucket.com/albums/t...dscar040-1.jpg


http://i157.photobucket.com/albums/t...R/102_0886.jpg

There is over $16,000 in mods on the car excluding any labor, seals, gaskets, new radiator, new starter, new axles, or even the actual price of the car. I have tons more pics that i wasnt able to post up.

Call Barinder @ 604-855-2220 , pm , or email sidhu_barinder@hotmail.com for more pics

awasome teg!!

^thanx bud... ttt!

..

bump for a sick DA and a fellow CI member. i envy the person who buys this car. very nice.

good luck on the sale bro

thanx teg tuner...daily bump!

ttt

tttt

to the top!

to the top

!@#$, sickkkkkkkkkkkkkkkkkkk

wanna trade for 00 SIR?

wow back at this tread again.. surprized its takin so long to sell a car this nice! come on ppl get it going! good luck wit sale

redline rev - naw...lookin for a 4door car or suv now. Thanx for the offer tho.

eurorsn - yea no kidding...no interest in a wicked da?! Thanks for the praise tho!

to thew top

ttttttttttttttttttttt

ttttttttttttttttt

Back to the top to see if any interest

ttt

ever dyno?
bump, sick teg wish mines was like this

^yup, same setup with stock head porting, type r valve train, and just a chipped ecu made 176 hp/ 150 ft/lbs tq . Should be upwards of 190 hp now and hopefully a lil more torque as well. Gotta get it dyno tuned again.

Wow..if i were to ever buy a teg...this would be it

http://calgary.kijiji.ca/c-cars-vehi...AdIdZ108927373

http://calgary.kijiji.ca/c-cars-vehi...AdIdZ108927373

trade for either plus cash? email me at firefighter_11 @hotmail.com

^thanx for the compliments guys!

integrasky...those are both the exact same link. Not interested in the pathfinder tho.

oops..my bad... sorry about that...

here is the other truck....

http://calgary.kijiji.ca/c-cars-vehi...AdIdZ116241784

lol..no worries. but not really my interest. Thanx for the offers tho.