Selling this amp, have recipts, mint condition 9.5/10 asking 450.00
•Reference Series Monoblock Class A/B Car Amplifier
•RMS Power Rating (14.4V): ◦4 ohms: 825 watts x 1 chan.
◦2 ohms: 1100 watts x 1 chan.
•Dynamic power output: 1450 watts x 1 chan.
•Optically isolated MOSFET power supply
•High current bipolar outputs
•E.H.V High voltage output circuitry
•Remote bass level input (remote level control sold separately)
•SLDIN-T.F Balanced line transmitter included
•LED power (green) and clipping (red) indicators
•Variable Bass Boost (0 to +12 dB bass boost at 50 Hz)
•SymbiLink acts as a line driver and can boost signal input up to 12dB (4-times)
•Improved noise rejection, lower system noise floor, reduced distortion, and up to 16V signal output
•Input mode switch (left, right, L/R sum)
•Mono channel operation
•Slew rate: 40V/uS
•Crossover x10 (550-5,500)
•Transient distortion (4 ohm, 40W): <0.03%
•Heavy duty textured pewter finished aluminum alloy heatsink or High-density split-dome convection heat sink for extreme heat dissipation
•SymbiLink balanced line inputs
•Gold-plated RCA level inputs
•Gold-plated high current screw terminals
•Input sensitivity: ◦Balanced (DIN): 250mV-10V
•Variable low-pass filter (55-550 Hz, 24 dB/octave)
•Variable low-pass filter (55-550 Hz, 24 dB/octave)
•Variable subsonic filter (24 dB at 15-50 Hz)
•Damping factor: >700 @ 4 Ohm
•CEA-2006 compliant amplifier
•Frequency response: 20-20,000 Hz
•Dimensions: 35"L x 7-1/2"W x 1-15/16"H
•4-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
Power Specifications - Subwoofer Channel
RMS Power @ 4 ohms
825 watts x 1 channel
RMS Power @ 2 ohms
1100 watts x 1 channel
RMS Power @ 1 ohm
Not Stable
Peak Power Output
1450 watts x 1 channel
Amplifier Specifications
Amplifier Class
AB
Number of Channels
1 - Mono
Total Peak Power Output
1450 watts
Total RMS Power Output
1100 watts
Maximum Input Gauge Size
8 AWG
Minimum Impedance Unbridged
2 ohms
Minimum Impedance Bridged
Not Bridgeable
THD at Rated RMS Power
<0.05%
Speaker Level Inputs
No
Preamp Outputs
No
Built-in Crossover
Low-pass (LP)
High-pass (HP)
Full (AP)
High-Pass Crossover Frequency
55 - 550 Hz
Low-Pass Crossover Frequency
55 - 550 Hz
Subsonic Filter
15 - 50 Hz
Signal-to-Noise Ratio
>90 dB
Channel Separation
N/A
Bass Boost
0 - 12 dB
Bass/Gain Remote
Optional (Accessory required and sold se
Fuse Rating
30A x 3
You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
The banners on the left side and below do not show for registered users!
